search

RUSTY'S TIPS ON HOW TO USE EPOXY MASTIC 121

RUSTY'S TIPS ON HOW TO USE EPOXY MASTIC 121

Product Code: -

THE BEST WAY TO USE EPOXY MASTIC 121 Mixing Epoxy?121?is a two pack modified epoxy high build coating. Comprising of base colour component A, and an equal amount of hardener component B. Mix components A and B together in equal amounts ie 100ml A to 100 ml B by measure. Allow to stand for approximately ten minutes to allow the chemical process to start. All of the data on our technical data sheets are calculated at 23 degrees C if the ambient temperature causes the Epoxy 121 to be a higher temperature the product will be thinner. At low temperatures 8 degrees c the product will be much thicker almost paste like. Thinning Epoxy 121 can be thinned up to a maximum of 15 ? 20% with the thinners provided in each kit. For spraying or fine brushing you will definitely need the thinner. " Top Tip" As a surface filler Without thinning EM121 can be used as a filler coat for imperfections on steel surfaces of up to .5 of a ml thick ( 500 um/microns) by mixing equal amounts of component A and component B without adding any thinner, allow to stand for ten minutes and then brush onto surface and scrape away excess to level the surface. For Brushing Depending on the temperature at the time of application Epoxy 121 can be easily brush painted. The addition of up to 15% of the thinners supplied may be added. Use a fully loaded wet brush and long strokes for the best finish. By Roller Epoxy 121 can be applied by roller, load the roller up fully before applying to the surface. Roller application requires twice the amount of coats to eradicate the chance of any misses ( holidays) in the coating. By Air Spray Use a spray gun with a 1.8 tip size smaller tips can be used on gravity fed spray guns. Thin the product up to 15% with the thinners provided. Over painting Epoxy 121 can be overpainted with any paint product. If fully cured ( over two weeks) a light sanding with an 320 grit abrasive will be required prior to painting. Seam sealing Apply Epoxy 121 to the bare steel area first, A seam sealer preferably polyurethane can then be applied over the epoxy 121 to seal the seam. Filling over EM 121 Due to the very hard nature of Epoxy 121 when cured we would recommend a sanding with an 80 grit and filling with Epoxy paste PC-7. Protect your precious metal Rusty? ? These how to guides are not technical data sheets or Health and safety data sheets those can be down loaded from our data sheet page. Any other technical information on drying times etc is available from the data sheet.

For more information on  RUSTY'S TIPS ON HOW TO USE EPOXY MASTIC 121  talk to  Rustbuster Ltd

Enquiry Form



More Products

3M 4251 HALF MASK RESPIRATOR P2

3M 4251 HALF MASK RESPIRATOR P2

HALF MASK RESPIRATOR P2 BY 3M Designed for effective protection against certain organic gases, vapours and particulates hazards up to specified conce...

Read More
Chassis Restoration Value Pack - Pure White

Chassis Restoration Value Pack - Pure White

Want to find a reliable company offering Chassis Restoration Value Pack - Pure White? You have come to the right spot! We are providing Chassis Restor...

Read More
EPOXY REPAIR PASTE PC-7

EPOXY REPAIR PASTE PC-7

PC-7 HEAVY DUTY EPOXY REPAIR PASTE This is a superb repair product, and pretty much essential to have in the garage, workshop or toolbox. It mixes as...

Read More

Read More

Read More

List your business

Would you like to register your company on one of the UK's largest and most effective Trade websites?

Are you looking for a reliable and consistent source of enquiries from your industry sector? Would you like to see why Find the Needle clients come back year after year to use our service? If so then feel free to register using the link 'here'.

Register
Office Address: